Heating, Ventilation and air Conditioning (HVAC) Systems

ICTD International Centre for Training and Development

How long?

  • 5 days
  • in person

ICTD International Centre for Training and Development

Disclaimer

Coursalytics is an independent platform to find, compare, and book executive courses. Coursalytics is not endorsed by, sponsored by, or otherwise affiliated with any business school or university.

Full disclaimer.

Reviews

Make sure this course is right for you.

Get unbiased reviews and personalized recommendations.

Who should attend

This course is intended for maintenance engineers, staff plant engineers, mechanical engineers, design engineers, electrical engineers, consulting engineers, inspection and repair managers, supervisors, operation, maintenance and technicians.

About the course

This course is designed for engineers and technicians from a wide range of abilities and backgrounds and will provide an excellent introduction to the fundamentals of Heating, Ventilation and Air-conditioning. It commences with a review of psychometric charts and then examines the factors that influence design choices, indoor air quality, load calculations and heating/ventilation and air-conditioning systems. Numerous tips and tricks throughout the program make it very practical and topical to your applications.

Ether it is a small warehouse or a complex hi-rise building, there is an increasing demand by Owners and Engineers to design and install the HVAC & R systems in a more efficient and cost-effective manner. Due to the on-going advances in HVAC & R technology, this demand is becoming a must and often controlled by new governmental regulations and engineering codes.

Realizing this need and the importance of the subject:

  • The details of heat load calculations, selection of appropriate equipment/system and the design of the ducts and piping networks.
  • A comprehensive design case study of a complete cold store including heat loads of individual rooms and the total cold store, selection of the appropriate equipment, design of the best layout including handling areas.
  • By the end of this program, participants will have enough knowledge to implement their daily assignments correctly and professionally.

Course Objectives

The aim of this program is to provide the participants with a complete and up-to-date overview of the area of Heating, Ventilation and Air-conditioning (HVAC). It commences with a review of psychometric charts and then examines the factors that influence design choices, indoor air quality, load calculations and heating/ventilation and air-conditioning systems. Numerous tips and tricks throughout the program make it very practical and topical to your applications.

Upon successful completion of this course, the delegates will be able to:

  • Maintain and troubleshoot HVAC systems
  • Understand and apply the psychometric chart
  • Design for good air quality
  • Perform basic load calculations
  • Initiate an effective inspection and maintenance program
  • Minimize forced outages and prevent serious damage to HVAC equipment
  • Provide an overview of the legislative requirements plus the essential steps and responsibilities for the maintenance and repair of HVAC Systems
  • Outline the technologies available for the efficient energy management using HVAC systems

Course Outline

### Day 1

  • HVAC Design, Maintain and troubleshoot
  • Heat load of a room
  • Heat load of a multi room complex.
  • The cooling capacity
  • The airflow rate
  • The fresh air requirements
  • The DX systems
  • The chilled water systems
  • Chilled water flow rates & piping sizing

Day 2

  • HVAC Design
  • Chilled water pumps selection
  • Building Management System and Control System
  • DX system piping sizing
  • Typical piping connections "DX units, chillers, pumps, AHU's and FCU's"
  • Insulation thickness & the criteria for condensation prevention
  • Duct sizing
  • Air filtration

Day 3

  • Maintain and troubleshoot & Cold stores design
  • The behavior of the fruit/vegetable after harvesting
  • How cold stores can extend the life of the products
  • How to decide the cold room dimensions
  • The heat load of the cold room (Chilling, frozen products, Potato and Onions)

Day 4

  • Cold stores design
  • Pre-cooling. "Wet cooling"
  • Selection of the refrigeration system components.
  • The insulation panels and doors
  • The docks "Levelers, shelters and doors"
  • Ventilation for potato and onions
  • Reference data and tables

Day 5

  • Operation and Maintenance
  • Documentation
  • As built hand over package documentation after completion of installation
  • Records and book keeping
  • PMR forms "Preventive maintenance routines"
  • Questions and answers
  • Case study

Course Methodology

A variety of methodologies will be used during the course that includes:

  • (30%) Based on Case Studies
  • (30%) Techniques
  • (30%) Role Play
  • (10%) Concepts
  • Pre-test and Post-test
  • Variety of Learning Methods
  • Lectures
  • Case Studies and Self Questionaires
  • Group Work
  • Discussion
  • Presentation

Videos and materials

Heating, Ventilation and air Conditioning (HVAC) Systems at ICTD International Centre for Training and Development

From  $3,300

Something went wrong. We're trying to fix this error.

Thank you for your application

We will contact the provider to ensure that seats are available and, if there is an admissions process, that you satisfy any requirements or prerequisites.

We may ask you for additional information.

To finalize your enrollment we will be in touch shortly.

Disclaimer

Coursalytics is an independent platform to find, compare, and book executive courses. Coursalytics is not endorsed by, sponsored by, or otherwise affiliated with any business school or university.

Full disclaimer.

Because of COVID-19, many providers are cancelling or postponing in-person programs or providing online participation options.

We are happy to help you find a suitable online alternative.